Skip to content
← All blogs

Garland, TX Heating System Repair: 5 Common Causes & Fixes

Heater not working right when a North Texas cold front hits? Before you bundle up, try a few safe checks. This guide shows quick ways to get heat back, when to call a pro, and how to prevent the next breakdown. If you need fast help, Arthur Heating & Air offers 24/7 emergency service across Dallas, Plano, Frisco, and more—often same day.

Start Here: Quick Safety and No‑Heat Triage

When a heater quits, begin with simple, safe steps:

  1. Confirm the thermostat is set to Heat and above room temperature.
  2. Replace or clean a dirty filter if you cannot see light through it.
  3. Check the breaker and furnace switch. Reset once if tripped.
  4. Look for error codes on the thermostat or equipment panel.
  5. For gas furnaces, verify the gas valve at the unit is set to On.

Stop and call a licensed pro if you smell gas, see scorch marks, hear loud bangs, or the breaker trips again after a reset.

Reason 1: Thermostat or Power Settings Are Off

Small setting mistakes cause many no‑heat calls.

What to check now:

  • Mode and temperature: Set to Heat and at least 3 degrees above current room temp.
  • Fan setting: Use Auto to avoid blowing room‑temperature air continuously.
  • Batteries: Some thermostats lose control when batteries fade. Replace them.
  • Scheduling or Hold: A programmed setback can block heating. Use Temporary Hold.
  • Power: Confirm the furnace switch is On and the service door is closed, which engages the safety switch.

Fix it yourself:

  • Replace batteries, clear any “Hold” or incorrect schedule, and reseat the thermostat on its base.
  • If your smart thermostat lost Wi‑Fi or power, reboot it and confirm the C‑wire or adapter is connected.

Call a pro if:

  • The display is blank with good batteries.
  • You see frequent short cycling or random on/off behavior.
  • Low‑voltage control wiring was recently altered.

Local tip: Smart thermostats can drift offline after power flickers common during Dallas cold snaps. A quick router reboot sometimes restores control.

Reason 2: Tripped Breaker or Blown Fuse

Heaters need steady power. A surge during a Blue Norther can trip breakers.

What to check now:

  • Electrical panel: Look for a breaker in the middle position and push it fully Off, then On once.
  • Service switch: Many attics in Plano, Allen, and Richardson have a light‑switch‑style disconnect. Make sure it is On.
  • GFCI outlets: If your condensate pump or air handler shares a GFCI, press Reset.

Fix it yourself:

  • Reset the breaker one time only. If it trips again, stop.
  • Clear stored items blocking airflow around the unit in small Dallas closets and attics to reduce overheating.

Call a pro if:

  • The breaker trips again, or you hear buzzing at the panel.
  • You suspect a shorted blower motor or control board. These need safe diagnostic tools and training.

Reason 3: Dirty Filter or Airflow Problems

Restricted airflow can overheat a furnace or cause a heat pump to run constantly and blow cool air.

What to check now:

  • Filter: If it is gray or you cannot see light through it, replace it.
  • Vents: Open supply and return vents, especially in rooms closed off for pets or guests.
  • Duct issues: Look for crushed or disconnected flex duct in the attic, a common culprit after storage moves.

Fix it yourself:

  • Use the correct filter size and MERV rating recommended by your system. Very high MERV filters can choke airflow on older equipment.
  • Vacuum return grilles and ensure furniture is not blocking them.

Call a pro if:

  • You notice hot and cold spots or unusually loud air noise.
  • Your system shuts off after a minute and restarts. That can indicate a limit switch reacting to heat buildup.

Pro insight: Our technicians often find that one closed return in a Frisco bonus room triggers repeated limit trips. A quick duct balance and filter change can restore steady heat.

Reason 4: Ignition or Pilot Problems on Gas Furnaces

Modern furnaces use hot‑surface igniters or spark igniters. Older units may have a standing pilot.

Signs of ignition trouble:

  • Furnace clicks repeatedly without lighting.
  • You hear the inducer fan, then shutdown.
  • You see an error code on the board or thermostat.

What you can try safely:

  • Turn power Off at the switch, wait 60 seconds, then On to clear a minor lockout.
  • Ensure the gas valve at the furnace is On and that other gas appliances work.

What needs a licensed pro:

  • Igniter replacement, flame sensor cleaning or replacement, pressure switch testing, and gas‑valve diagnostics.
  • Combustion safety checks and venting inspections. Safety is non‑negotiable.

If your pilot will not stay lit:

  • A faulty thermocouple, dirty pilot or weak gas pressure may be involved. Skip DIY here and schedule service.

Reason 5: Heat Pump Issues in Cold Weather

Heat pumps can look broken when they are defrosting or when outdoor coils are dirty.

Normal vs. problem signs:

  • Normal: Steam cloud during defrost, fan stopping briefly, then heat resumes.
  • Problem: Outdoor unit iced over for hours, loud metal grinding, or warm air inside is weak.

What to check now:

  • Thermostat mode: Make sure Heat is selected. If very cold, Emergency Heat can provide backup for the night.
  • Air filter: A clogged filter reduces heat output.
  • Outdoor unit: Clear leaves and debris 18 inches around the unit. Do not chip ice.

Fix it yourself:

  • Gently rinse the outdoor coil with a hose on a mild day to remove dirt. Power Off first.
  • Switch to Emergency Heat if the outdoor unit is frozen, then schedule service.

Call a pro if:

  • You suspect low refrigerant, a failing reversing valve, or sensor issues.
  • The outdoor fan or compressor will not start.

Our team handles electrical and control board repairs, refrigerant leak detection and recharge, compressor and fan motor work, thermostat and sensor troubleshooting, defrost cycle repairs, and airflow and duct checks.

When to Repair vs. Replace

A smart decision saves money and frustration.

Repair is usually smart when:

  • The unit is under 10 years old and well maintained.
  • The issue is minor, like a dirty sensor or failed capacitor.

Consider replacement when:

  • Your furnace or heat pump is 12–15+ years old and needs frequent repairs.
  • The heat exchanger is cracked or the system is unsafe.
  • Your energy bills keep rising despite recent tune‑ups.
  • Your system uses outdated components and struggles to maintain comfort.

Why replacement can pay off in Dallas‑area homes:

  • New systems deliver steadier temperatures during quick temperature swings.
  • Quieter operation and improved indoor air quality with compatible filtration and humidity control.
  • Strong warranties and financing options reduce risk.

We provide free estimates for new equipment and can often install the same day, so you are not stuck shivering through a cold snap.

Preventive Maintenance for North Texas Homes

A little care prevents the most common no‑heat calls.

Recommended frequency:

  • Twice‑a‑year professional inspections for heat and cool seasons.
  • Change 1‑inch filters every 1–2 months during heavy use. Larger media filters may last 3–6 months.

What a pro tune‑up includes:

  • Cleaning and testing burners, flame sensors, and igniters on furnaces.
  • Electrical checks on motors, capacitors, and control boards.
  • Heat pump checks for refrigerant level, defrost cycle, and reversing valve operation.
  • Duct and airflow verification, thermostat calibration, and safety controls testing.

Homeowner checklist between visits:

  1. Keep 18–24 inches clear around indoor and outdoor units.
  2. Vacuum returns and supply grilles.
  3. Replace filters on schedule and date the frame.
  4. After storms, listen for new rattles or vibration.
  5. Before the first cold week, test Heat mode for 10 minutes to confirm ignition.

Why plan with Arthur Heating & Air:

  • Our Comfort Club membership includes regularly scheduled maintenance visits, priority service, discounts on parts and labor, and 24/7 emergency service at no extra charge. Plans start at $14.95 per month.

Why Dallas‑Area Homeowners Choose Arthur Heating & Air

  • Fast response: Same‑day service and 24/7 emergency coverage across Dallas, Plano, Garland, Frisco, Irving, and nearby cities.
  • Proven quality: BBB A+ accredited and nationally certified technicians who explain options clearly.
  • Licensed and insured: Texas License #TACLB29253E.
  • Honest pricing: Upfront estimates, financing options, and a 100% satisfaction guarantee.
  • One‑call solution: Installation, repair, maintenance, indoor air quality, and duct services in one place.

If your heater is still not working after the steps above, schedule service and we will get your comfort back quickly and safely.

Special Offers for Heating Service

  • $25 OFF System Repair. Mention “$25 OFF System Repair” when you book. Not valid with other offers. Limit one per customer.
  • $49 Service Call for diagnostic/repair visits. Valid Jan 1, 2026 – Dec 31, 2026.
  • $250 OFF Full System Upgrade. Applies to qualifying HVAC installation. Not valid with other offers.
  • Comfort Club Maintenance from $14.95/month. Includes bi‑annual tune‑ups, priority service, and repair discounts.

Call (469) 515-2900 or book at http://callarthurair.com/ to claim an offer. Electronic versions are accepted. Restrictions may apply.

What Homeowners Are Saying

"Hugo was prompt, friendly, and knowledgeable. He solved my furnace problem and checked the entire system for any issues. Authur is the only company I call !"
–ibhumpty, Heating Repair

"I'm happy we found Arthur Heating & Air! Its great that they do not just contract out their labor and have actual employees of the company come out. Our heater needs much more love than we can afford right now but David and Jack were able to quote me great price to get it up and running again. Thanks so much!"
–Shawn & Jessica B., Heater Service

"Awesome service!!! We really appreciated the care and respect that Marcos and Erick displayed for our home as they installed our new heating and air system. The system is far superior to our old one... Our family highly recommend Arthur HVAC..."
–Larry D., System Installation

"Fantastic experience. Arthur H & A installed a new system in our home... They did it the same day and were courteous, professional and our new system has made a tremendous difference."
–Kevin B., System Installation

Frequently Asked Questions

Why is my heater blowing cold air?

A dirty filter, incorrect thermostat mode, or an overheated furnace that trips a safety can cause cool air. Replace the filter, set the thermostat to Heat and Auto, then try again. If it persists, schedule service.

Is it safe to reset a tripped furnace breaker?

Reset it once. If it trips again, stop and call a licensed technician. Repeated trips indicate an electrical problem such as a shorted motor or control board that needs professional diagnostics.

How often should I service my heater in Dallas?

Plan professional inspections twice a year, before heating and cooling seasons. Change standard 1‑inch filters every 1–2 months during heavy use to keep airflow strong and parts protected.

What does emergency heat on a heat pump do?

Emergency Heat bypasses the outdoor unit and runs electric or gas backup heat. Use it only if the outdoor unit fails or is iced over, then schedule a repair to restore normal efficiency.

When should I replace instead of repair?

Consider replacement if your system is 12–15+ years old, needs frequent repairs, has a cracked heat exchanger, or cannot maintain comfort. New systems offer better efficiency, comfort, and warranties.

Bottom Line

If your heater is not working, start with thermostat, breaker, and filter checks. For ignition issues, heat pump faults, or repeated shutdowns, call Arthur Heating & Air. We serve Dallas, Plano, Irving, Garland, Frisco, Mesquite, Carrollton, Richardson, Allen, and Rowlett.

Ready for Warmth? Schedule Now

Call (469) 515-2900 or book at http://callarthurair.com/. Mention "$25 OFF System Repair" or ask about our $49 service call in 2026. Need a new system? Get a free estimate and $250 OFF a full upgrade today.

Call (469) 515-2900 or schedule at http://callarthurair.com/ for 24/7 heating help. Mention "$25 OFF System Repair" or join the Comfort Club from $14.95/month for priority care and bi‑annual tune‑ups.

About Arthur Heating & Air

Arthur Heating & Air is a family‑owned, BBB A+ accredited HVAC company serving Dallas, Plano, Frisco, Irving, and nearby cities. We are licensed and insured (License #TACLB29253E) and available 24/7 with same‑day service. Our Comfort Club keeps systems tuned for less, and we back our work with a 100% satisfaction guarantee. Count on honest recommendations, clear pricing, financing options, and skilled bilingual technicians who respect your home.

Sources12

Source links open in a new tab.

Need Help With Your Home?

Turn helpful advice into action with professional service from our experienced technicians.

Call nowSchedule service