Skip to content
← All blogs

Plano, TX HVAC Repair: 5 Common Furnace Issues & Fixes

If your home is chilly and you are searching for furnace repair near me, you are not alone. North Texas cold snaps can expose small furnace issues that quickly turn into no‑heat emergencies. Below are the top five furnace problems we see most often in Dallas–Fort Worth, how to fix them fast, and when to call a pro. Use our quick checks to stay safe, warm, and in control of your budget.

1) The furnace will not ignite or there is no heat

When the thermostat calls for heat and nothing happens, start with the basics.

  1. Set the thermostat to Heat and raise the setpoint 3 to 5 degrees above room temperature.
  2. Check the furnace power switch and your breaker panel. Reset a tripped breaker once. If it trips again, stop and call a pro.
  3. For gas furnaces, confirm the gas shutoff is parallel with the pipe. If you smell gas, leave the home and call your utility and an HVAC technician.
  4. Inspect the furnace door. Many units have a safety switch that kills power when the panel is not fully seated.
  5. Look at the furnace status light. A steady light is usually normal. A flashing code points to a fault such as pressure switch, ignition, or limit issues.

Fast fixes a homeowner can try:

  • Replace a dead thermostat battery.
  • Replace a clogged air filter to restore airflow, then restart the furnace.
  • If you have a pilot light system, relight only if your manual instructs it and you are comfortable. If the flame will not stay lit, stop and schedule service.

Common pro repairs:

  • Clean or replace a dirty flame sensor that prevents ignition.
  • Repair or replace a failed hot surface igniter or spark igniter.
  • Correct pressure switch faults caused by blocked condensate drains, cracked hoses, or vent obstructions.

Safety tip: Install and test carbon monoxide detectors on every level. If your furnace fails to ignite repeatedly, do not keep cycling power. That can flood the system with unburned gas and stress components.

"Clint arrived on site within an hour, immediately diagnosed the issue and fixed the problem. My customer was so impressed I was able to right the issue so quickly in the middle of August and saved all of us a major headache. I would definitely refer Clint and Arthur Heating & Air to anyone in need of reliable, honest and professional HVAC service."

2) Short cycling or the furnace starts and stops repeatedly

Short cycling means the furnace fires, runs briefly, then shuts down before the home is warm. Left unchecked, it wastes energy and wears out parts.

Quick checks:

  1. Air filter: A packed filter overheats the heat exchanger and trips the high‑limit switch. Replace the filter, then restart at the thermostat.
  2. Supply and return vents: Open and clear them. Do not close more than one or two vents because static pressure spikes cause overheating.
  3. Thermostat location: If it is near a register, sunny window, or space heater, it can misread the room and cause frequent cycling. Move it or use remote sensors.

Likely professional fixes:

  • Clean the flame sensor so the control board gets a stable flame signal.
  • Test and replace a weak inducer motor or pressure switch that fails mid‑cycle.
  • Verify proper gas pressure and adjust if the flame is unstable.
  • Inspect the condensate trap and drain on high‑efficiency furnaces. A blockage mimics a pressure fault and shuts the system down.

Why it happens in DFW: Many attic furnaces in North Texas fight dust from roof decking and insulation. Filters load faster in winter start‑ups. If short cycling returns within days of a filter change, call a technician to evaluate the limit circuit and airflow design.

"Arthur Heating and Air has been a Home Run every time! They did an excellent job on installation six years ago and they quickly found and corrected the problem this time. I heartily recommend them!"

3) Weak airflow or some rooms are cold

Uneven heating shows up first in far bedrooms and over garages. Your furnace may be fine but starved for air.

Homeowner steps:

  1. Check the filter first. A 1‑inch filter can clog in 30 to 60 days during heavy use.
  2. Make sure the blower door is on tight. Air leaks at the cabinet reduce system pressure.
  3. Open all supply registers at least halfway. Confirm returns are not blocked by furniture.
  4. If you recently had renovation or roof work, look for crushed or disconnected flex ducts in the attic.

Professional solutions:

  • Measure static pressure and temperature rise. The correct temperature rise is listed on your furnace data plate. Out‑of‑range numbers indicate duct or blower problems.
  • Clean the blower wheel. Dust buildup reduces airflow by hundreds of CFM.
  • Seal and repair duct leaks. North Texas attics swing from hot to cold, which stresses tape and mastic over time.
  • Right‑size or balance the system. Zoning, damper adjustments, and return upgrades can solve chronic cold rooms.

Pro insight: If multiple vents are weak, never upsize the filter MERV rating without checking blower capacity. Too restrictive filters protect coils but can choke airflow.

"These guys are no joke! They came out on a Friday to investigate a foul smell. Included pictures with each issue and an explanation of the issue and a plan for a solution. I approved the repairs and and they were back on Monday to perform the fix. This wasn't a small job by any means and they went above and beyond to take care of other issues not covered in the quote for free. I recommend that everyone use these guys."

4) Strange noises: banging, screeching, rumbling

Sounds point to specific problems you can triage quickly.

  • Banging at start: Often delayed ignition or expanding sheet metal. Turn off the furnace and call a pro to check burners and gas pressure.
  • Screeching: Usually a blower or inducer motor bearing. Running it can cause motor failure. Schedule service soon.
  • Rumbling or booming during operation: Could be burners, a cracked heat exchanger, or airflow restriction. This is a safety concern.
  • Rattling: Loose panels or vent connections. Tighten screws and confirm the flue is secure.

Homeowner checklist:

  1. Replace the filter and restart to rule out overheating noise.
  2. Confirm the furnace is level and the cabinet screws are snug.
  3. Look for sagging flex ducts that snap when air starts.

Professional repairs:

  • Clean and align burners for smooth ignition.
  • Replace worn blower bearings or the entire motor assembly if amperage is high.
  • Inspect the heat exchanger. If cracked, do not operate the furnace. Replacement is the only safe path.

"Jack did an outstanding job getting our HVAC system back up and running. When he discovered a larger issue with the system, he took the time to sit down with us and clearly explain our best options moving forward. His professionalism, excellent customer service, and willingness to go above and beyond made the entire experience stress‑free. Jack was wonderful to work with, and we highly recommend him!"

5) Burning smell, furnace runs but air is cool, or blower will not stop

These issues range from normal to urgent. Sort them fast with simple checks.

Burning or dusty smell at first heat:

  • Normal for the first cycle of the season as dust burns off the heat exchanger. The odor should fade within an hour. Open a window briefly if needed.

Burning plastic or electrical smell:

  • Not normal. Turn off power at the switch or breaker and schedule service. Motors, wiring, and control boards may be failing.

Furnace runs but the supply air is cool:

  1. Confirm the thermostat is not set to Fan On. Use Auto.
  2. Replace the filter and restart.
  3. If you have a heat pump with a gas furnace, the thermostat may be calling for the wrong heat source. This needs professional setup.

Blower will not stop:

  • A stuck fan relay or a tripped high‑limit switch can lock the blower on. Replace the filter, reset power once, and call for service if the fan continues nonstop.

When to replace instead of repair

  • Frequent limit trips, a cracked heat exchanger, or repair costs over 30 percent of a new unit often signal replacement. Many Dallas homes have older 80 percent furnaces in the attic. Upgrading to a modern, sealed‑combustion furnace can improve comfort and safety while trimming utility costs.

"Nerio did a thorough job of servicing our HVAC system, and diagnosing the problems. He offered thoughtful options for repair, and put Arthur Heating & Air's best foot forward for making decisions for repair or replacement. He was knowledgeable and experienced, and treated us with warmth and respect."

Pro maintenance that prevents most furnace breakdowns

A small amount of prevention goes a long way in North Texas, where furnaces work hardest during sudden Blue Norther cold fronts.

What to schedule before peak season:

  • Precision furnace tune‑up: Clean burners, flame sensor, and blower wheel. Verify gas pressure, temperature rise, and safety controls.
  • Filter plan: Stock 3 to 6 months of filters that match your blower capacity and allergy needs.
  • Duct inspection: Seal and support flex runs in the attic, especially after roof or insulation projects.
  • Thermostat and sensors: Test calibrations and replace batteries. Smart thermostats should be properly wired for heat mode.

Why homeowners choose our program:

  • 24/7 emergency availability for members when the unexpected happens.
  • Same‑day response with stocked trucks for the most common parts, which avoids multiple trips.
  • Honest recommendations with upfront pricing so you decide what is best for your home.

Local credibility you can verify:

  • Arthur Heating & Air is licensed and insured. Texas HVAC License TACLB29253E.
  • We serve Dallas, Plano, Frisco, Garland, Allen, Rowlett, and more with bilingual support in English and Spanish.

When to call a professional immediately

  • You smell gas or suspect a carbon monoxide issue.
  • The breaker trips again after one reset.
  • The furnace cycles repeatedly and the house does not warm up.
  • You see water under a high‑efficiency furnace or the vent is frosted shut.
  • The flame is yellow instead of steady blue.

If any of these occur, power the system down and schedule service. Same‑day and 24/7 emergency support are available in the Dallas–Fort Worth area.

Special Offer: Save $25 on Furnace Repair

Save $25 on system repair. Use code ARTHUR25 before 2026-12-31. Must mention coupon at time of service. Not valid with other offers. Limit one per customer. Arthur Heating & Air honors electronic coupons.

Call (469) 515-2900 or schedule at http://callarthurair.com/ to claim your discount today.

Frequently Asked Questions

How do I reset my furnace safely?

Turn the thermostat to Off, switch power off at the furnace for 60 seconds, replace a dirty filter, then turn Heat back On. If it fails again, call a pro.

What filter should I use for my furnace?

Use the size listed on your return grille or cabinet. A MERV 8 to 11 filter works for most homes. Higher MERV can restrict airflow if the blower is not sized for it.

Why does my furnace smell when first turned on?

Dust on the heat exchanger burns off after months of no use. The smell should fade within an hour. If it smells like burning plastic or wiring, shut it down and call.

How often should my furnace be serviced?

Have a professional tune‑up once a year before winter. Cleaning burners, checking safety controls, and verifying gas pressure prevent most breakdowns.

Is short cycling dangerous?

Short cycling can overheat the heat exchanger and stress components. Replace the filter and check vents. If it continues, schedule service to protect the furnace.

Wrap‑Up

You now know the top five furnace problems, quick homeowner fixes, and the red flags that need a professional. If you are searching for furnace repair near me in Dallas–Fort Worth, we are ready to help with same‑day service, honest pricing, and long‑lasting repairs.

Next Step: Call or Schedule Now

  • Call Arthur Heating & Air at (469) 515-2900
  • Book online at http://callarthurair.com/
  • Mention ARTHUR25 to save $25 on your furnace repair before 2026-12-31

Stay warm, stay safe, and let our licensed team get your heat back fast.

Call now: (469) 515-2900 · Schedule: http://callarthurair.com/ · Coupon: ARTHUR25 for $25 off repair before 2026-12-31

About Arthur Heating & Air

Arthur Heating & Air is a family‑owned HVAC company serving Dallas–Fort Worth with licensed, insured technicians focused on fast, honest service. We offer same‑day appointments, 24/7 emergency response, bilingual support, clear pricing, financing options, and strong warranties. From precision repairs to energy‑smart installations and maintenance, our team delivers long‑lasting solutions homeowners trust. License TACLB29253E. Proudly serving Dallas, Plano, Frisco, Garland, Allen, Rowlett, and nearby cities.

Sources12

Source links open in a new tab.

Need Help With Your Home?

Turn helpful advice into action with professional service from our experienced technicians.

Call nowSchedule service